EnGenius EOC-2610
*Cara Reset Engenius Eoc 2610
*Cara Setting Engenius Eoc 2610 Setup
EOC-2610 is a Long Range outdoor wireless Access Point / Client Bridge that operates seamlessly in the 2.4GHz frequency spectrum and provides high bandwidth up to 108Mbps with SuperG. EOC-2610 features high transmit output power and high receive sensitivity. High output power and high sensitivity can extend range and coverage to reduce the roaming between Access Points and to deliver a more stable wireless connection. It also reduces deployment expenses on the equipments.Now you can update your access point senao eoc-2610 to dd-wrt firmwares
EOC-2610 is a long range outdoor wireless Access Point and Client Bridge that operates seamlessly in the 2.4GHz frequency spectrum. It features high transmitted output power and high receivable sensitivity. High output power and high sensitivity can extend range and coverage to reduce the roaming between Access Points to get a more stable. (The EOC 2610 does not support universal wireless repeating so another EOC-2610 is required as the source access point.) Search the Wifithoughts forum to find better information than provided by EnGenius. POE injector is 24 volts rather than the more typical 48 volts.
*Configure your local computer IP address to 192.168.1.11.
*Connect to the RedBoot bootloader by telnet on 192.168.1.10 (some have 192.168.1.1) and port 9000. Enter telnet command at the moment Ethernet LED lights up after powering on the EOC-2610 board (about 10 sec. after power on). Because timeslot for this is short, you might need several tries.
*Enter the RedBoot console by pressing CTRL+C.
*Copy linux.bin to your TFTP server directory. (once you installed a tftp server)
*Configure the RedBoot bootloader IP and TFTP server settings using ip_address -l [local ip address] -h [remote server address]
Flash the unit by entering the following commands:
RedBoot> fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xa87e0000-0xa87f0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
RedBoot> load -r -b 0x80041000 linux.bin
Using default protocol (TFTP)
-
Raw file loaded 0x80041000-0x80663fff, assumed entry at 0x80041000
RedBoot> fis create linux
... Erase from 0xa8030000-0xa8653000: ...................................................................................................
... Program from 0x80041000-0x80664000 at 0xa8030000: ...................................................................................................
... Erase from 0xa87e0000-0xa87f0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
RedBoot> fconfig
Enter the bootscript:
fis load -l linux
exec
Save the config and do:Cara Reset Engenius Eoc 2610
RedBoot> reset
You can download firmware dd-wrt .bin files click hereuse search to find fiirmware.Cara Setting Engenius Eoc 2610 Setup
EnGenius 2610 / 1650 client router configuration.
If you purchased on of our bridge kits you will need 2 standard straight through ethernet cables available at your local store. One cable will run from your computer to the power injector the other from the PoE side of the injector to the bridge up to 300 feet away. You will also need to switch the antenna over to external ( next to the connector).
We are going to show you how to use the unit to connect to a remote access point in 8 easy steps. This is the perfect configuration for boaters, RVers and many other mobile applications.
1) set your computer IP address to 192.168.1.100
2) log into the eoc-2610 at 192.168.1.1 un admin pw admin, click on system / system properties select client router mode and hit apply.
3) click on router / LAN settings make the following changes (the address of the unit will now be 192.168.123.1 do not forget this)
4) change your computers ip address back to DHCP for IP and DNS like below.
5) log into the unit at 192.168.123.1 , click on router / WAN settings change connection type to DHCP and hit apply.
6) Now lets turn the power up on this puppy click on wireless / wireless advanced and select 28dBm hit apply.
7) click on wireless / wireless network site survey button , select the AP to connect to by clicking the MAC address and click apply. (Try and connect to a open AP where under the security column you see NONE, if the AP has encryption enabled you must get the key from the owner and enter it under encryption)
8) Click on status connection status you should see associated next to connection status and have a IP address under WAN / IP address. If not try another AP or move closer.
You should now have a Internet connection! To manage the bridge in the future go to 192.168.123.1 and follow step 6.
